A network administrator is verifying LLQ configuration on a router. The administrator wants to confirm that the policy map is correctly applied to the interface and that the class maps are matching traffic as expected. Which two commands together provide this information?

show class-map and show policy-map

show running-config and show policy-map interface

show access-lists and show policy-map

show interface and show ip route

A network engineer is configuring LLQ on a router with multiple WAN interfaces. The same policy map needs to be applied to two different interfaces with different bandwidths: one is a 10 Mbps link and the other is a 1.544 Mbps T1. The policy uses absolute bandwidth values. What is the correct approach?

Use bandwidth percent in the policy map

Apply the policy to the physical interface only

Apply the same policy map to both interfaces

Create two separate policy maps with bandwidth values appropriate for each interface

A network engineer has applied an LLQ policy to a WAN interface in the output direction. After implementation, voice quality is still poor. The show policy-map interface command shows that the voice class is not matching any packets. What is the most likely cause?

The policy is applied in the wrong direction

The class map is using match-all instead of match-any

The interface is not receiving any voice traffic

The voice traffic is not being marked with the DSCP value specified in the class map

CiscoCertified Network Professional Collaboration

Domain 6Objective 4

6.4 Configure LLQ (class Map, Policy Map, Service Policy) 350-801 Practice Questions (Page 2)

Part of the Media and QoS domain, which accounts for 10% of the 350-801 exam. Cisco does not publish an official question count, but from its 120-minute exam (~50–80 total, ~5–8 in this domain), expect 1–2 from this objective — we provide 16 practice questions to prepare you well beyond it. (estimate)

16questions here

4free pages

5concepts

10%of the exam

Questions 6–10

6foundation · easy
Which policy-map configuration command is used to associate a class map with QoS actions?
Select an answer first
7application · medium
A network administrator is verifying LLQ configuration on a router. The administrator wants to confirm that the policy map is correctly applied to the interface and that the class maps are matching traffic as expected. Which two commands together provide this information?
Select an answer first
8expert · hard
A network engineer is configuring LLQ on a router with multiple WAN interfaces. The same policy map needs to be applied to two different interfaces with different bandwidths: one is a 10 Mbps link and the other is a 1.544 Mbps T1. The policy uses absolute bandwidth values. What is the correct approach?
Select an answer first
9foundation · easy
Which command is used to create a policy map and enter policy-map configuration mode?
Select an answer first
10expert · hard
A network engineer has applied an LLQ policy to a WAN interface in the output direction. After implementation, voice quality is still poor. The show policy-map interface command shows that the voice class is not matching any packets. What is the most likely cause?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to 350-801

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Cisco. “350-801” is a trademark of its owner, used for identification only.

6.4 Configure LLQ (class Map, Policy Map, Service Policy) 350-801 Practice Questions (Page 2)

Questions 6–10

Which policy-map configuration command is used to associate a class map with QoS actions?

A network administrator is verifying LLQ configuration on a router. The administrator wants to confirm that the policy map is correctly applied to the interface and that the class maps are matching traffic as expected. Which two commands together provide this information?

Which command is used to create a policy map and enter policy-map configuration mode?

A network engineer has applied an LLQ policy to a WAN interface in the output direction. After implementation, voice quality is still poor. The show policy-map interface command shows that the voice class is not matching any packets. What is the most likely cause?

Keep studying — Media and QoS