A Junos router is connected to a segment where IPv6 hosts are unable to discover the default gateway. The router has an IPv6 address configured on the interface, and the interface is operationally up. Which command should the engineer use to verify that the router is sending router advertisements on that interface?

show ipv6 route interface ge-0/0/0

show ipv6 router-advertisement interface ge-0/0/0

show ipv6 neighbors interface ge-0/0/0

Which statement correctly describes the EUI-64 process for generating an IPv6 interface identifier?

It uses the MAC address but only the first 24 bits, and pads the rest with zeros.

It generates a random 64-bit identifier and combines it with the prefix, with no relation to the MAC address.

It uses the MAC address as-is and appends it to the 64-bit prefix to form the full address.

It inserts FF:FE in the middle of the 48-bit MAC address and flips the Universal/Local (U/L) bit.

A service provider is implementing NAT64 to allow IPv6-only clients to access IPv4-only servers. The NAT64 gateway has an IPv4 address pool of 203.0.113.0/24. What is the purpose of the IPv4 address pool in this configuration?

To provide IPv4 addresses for the NAT64 gateway's own interfaces

To translate IPv4 destination addresses to IPv6 destination addresses

To assign IPv4 addresses to IPv6 clients

To translate IPv6 source addresses to IPv4 source addresses

Juniper NetworksCertified Specialist, Service Provider Routing and Switching (JNCIS-SP)

Domain 8Objective 4

Configure, Monitor, or Troubleshoot IPv6 Technologies JN0-364 Practice Questions (Page 2)

Part of the IPv6 domain, which makes up ~5% of our current practice bank. Juniper Networks does not publish an official question count, but from its 90-minute exam (~35–60 total, ~2–3 in this domain), expect 1–1 from this objective — we provide 21 practice questions to prepare you well beyond it. (estimate)

21questions here

5free pages

7concepts

Questions 6–10

6foundation · easy
Which IPv6 address type is always confined to a single link and is automatically configured on every interface?
Select an answer first
7application · medium
A Junos router is connected to a segment where IPv6 hosts are unable to discover the default gateway. The router has an IPv6 address configured on the interface, and the interface is operationally up. Which command should the engineer use to verify that the router is sending router advertisements on that interface?
Select an answer first
8foundation · easy
Which statement correctly describes the EUI-64 process for generating an IPv6 interface identifier?
Select an answer first
9application · medium
A service provider is implementing NAT64 to allow IPv6-only clients to access IPv4-only servers. The NAT64 gateway has an IPv4 address pool of 203.0.113.0/24. What is the purpose of the IPv4 address pool in this configuration?
Select an answer first
10foundation · easy
Which IPv6 tunneling mechanism encapsulates IPv6 packets in IPv4 packets and is typically used for site-to-site tunnels where the tunnel endpoints are explicitly configured?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to JN0-364

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Juniper Networks. “JN0-364” is a trademark of its owner, used for identification only.

Configure, Monitor, or Troubleshoot IPv6 Technologies JN0-364 Practice Questions (Page 2)

Questions 6–10

Which IPv6 address type is always confined to a single link and is automatically configured on every interface?

Which statement correctly describes the EUI-64 process for generating an IPv6 interface identifier?

A service provider is implementing NAT64 to allow IPv6-only clients to access IPv4-only servers. The NAT64 gateway has an IPv4 address pool of 203.0.113.0/24. What is the purpose of the IPv4 address pool in this configuration?

Which IPv6 tunneling mechanism encapsulates IPv6 packets in IPv4 packets and is typically used for site-to-site tunnels where the tunnel endpoints are explicitly configured?

Keep studying — IPv6