During a manual ONIE installation of SONiC, the engineer watches the console output. The process reaches the point where the image is being written to the disk. Which output indicates that the installation is progressing correctly?

The switch reboots automatically within a few seconds of starting the install.

A series of progress bars showing the image extraction and write percentage.

A message stating 'ONIE: Image installation complete' immediately after the command is issued.

The ONIE prompt returns without any error messages.

After a manual ONIE installation, the switch boots to the SONiC login prompt. The engineer logs in and runs 'show version', which displays the correct SONiC version. However, the engineer notices that the management interface is not configured. What does this indicate?

The installation was successful, but the initial configuration has not been applied.

The image was corrupted during installation.

The installation failed because the management interface is not configured.

The switch is still in ONIE mode.

A network engineer is deploying SONiC on a Dell switch in a data center. The switch is currently running the vendor's factory OS. The engineer has a console connection and a management IP configured on the switch. The SONiC image is hosted on an HTTP server that is reachable from the management network. The engineer wants to perform the installation with minimal disruption and without using USB media. What is the correct sequence of steps?

Run onie-install -i http://server/sonic.bin from the factory OS CLI.

Reboot the switch, interrupt boot to enter ONIE, then run onie-install -i http://server/sonic.bin

Copy the image to the switch's flash and run onie-install from the ONIE shell after booting into ONIE.

Use the factory OS's upgrade command to install SONiC directly.

A technician is performing a manual ONIE installation on a Dell switch. The switch has been booted into ONIE, but the technician accidentally ran 'onie-install -i http://wrong-url/sonic.bin' and the command failed. The technician wants to retry with the correct URL. What should the technician do?

Manually delete the partially downloaded image from the disk.

Simply run the correct onie-install command again.

Reboot the switch and re-enter ONIE before retrying.

Run 'onie-install --clean' first to clear the failed attempt.

Which of the following is a hardware prerequisite for installing SONiC on a switch using the ONIE manual method?

A USB drive with at least 32 GB capacity

A dedicated management server with at least 16 GB RAM

A switch with at least 4 GB of NVRAM

Dell SONiC Deploy

Domain 2Objective 2

Install SONiC Using the ONIE Manual Method SONIC-DEPLOY Practice Questions (Page 3)

Part of the SONiC Installation domain, which accounts for 11% of the SONIC-DEPLOY exam.

24questions here

5free pages

5concepts

11%of the exam

Questions 11–15

11application · medium
During a manual ONIE installation of SONiC, the engineer watches the console output. The process reaches the point where the image is being written to the disk. Which output indicates that the installation is progressing correctly?
Select an answer first
12expert · medium
After a manual ONIE installation, the switch boots to the SONiC login prompt. The engineer logs in and runs 'show version', which displays the correct SONiC version. However, the engineer notices that the management interface is not configured. What does this indicate?
Select an answer first
13expert · medium
A network engineer is deploying SONiC on a Dell switch in a data center. The switch is currently running the vendor's factory OS. The engineer has a console connection and a management IP configured on the switch. The SONiC image is hosted on an HTTP server that is reachable from the management network. The engineer wants to perform the installation with minimal disruption and without using USB media. What is the correct sequence of steps?
Select an answer first
14expert · medium
A technician is performing a manual ONIE installation on a Dell switch. The switch has been booted into ONIE, but the technician accidentally ran 'onie-install -i http://wrong-url/sonic.bin' and the command failed. The technician wants to retry with the correct URL. What should the technician do?
Select an answer first
15foundation · medium
Which of the following is a hardware prerequisite for installing SONiC on a switch using the ONIE manual method?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to SONIC-DEPLOY

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Dell Technologies. “SONIC-DEPLOY” is a trademark of its owner, used for identification only.