A network engineer is configuring a Dell SONiC switch to act as a Layer 3 gateway for a new server subnet (10.10.20.0/24). The engineer assigns the IP address 10.10.20.1/24 to Ethernet 1/1, but the connected servers cannot reach the gateway. The engineer verifies that the physical link is up and the servers are configured correctly. Which command should the engineer run FIRST to confirm that the IP address is properly assigned to the interface?

show running-config interface Ethernet 1/1

show interfaces status Ethernet 1/1

A service provider is deploying a Dell SONiC switch to interconnect two IPv6-only customer networks. The engineer must configure Ethernet 1/3 with a global unicast address 2001:db8:1:1::1/64 and ensure that the interface can automatically generate its link-local address for neighbor discovery. After configuring the global address, the engineer wants to verify that both addresses are present on the interface. Which command accomplishes this?

show running-config interface Ethernet 1/3

show ipv6 interface Ethernet 1/3

A network architect is planning the deployment of a Dell SONiC switch as a core router. The architect needs to connect multiple transit networks, each on a different subnet, using a single physical interface to conserve ports. What is the most appropriate way to achieve this?

Configure the interface as a trunk and use SVIs for each subnet

Configure multiple secondary IP addresses on the Ethernet interface

Create a separate VLAN for each subnet and use subinterfaces

Use a single IP address and rely on proxy ARP

Dell SONiC Deploy

Domain 4Objective 1

Administer L3 IP Addressing on Ethernet Ports SONIC-DEPLOY Practice Questions (Page 1)

Part of the Routing domain, which accounts for 24% of the SONIC-DEPLOY exam.

18questions here

4free pages

5concepts

24%of the exam

Questions 1–5

1application · medium
A network engineer is configuring a Dell SONiC switch to act as a Layer 3 gateway for a new server subnet (10.10.20.0/24). The engineer assigns the IP address 10.10.20.1/24 to Ethernet 1/1, but the connected servers cannot reach the gateway. The engineer verifies that the physical link is up and the servers are configured correctly. Which command should the engineer run FIRST to confirm that the IP address is properly assigned to the interface?
Select an answer first
2foundation · easy
Which SONiC command shows the operational state (up/down) of an Ethernet interface?
Select an answer first
3application · medium
A service provider is deploying a Dell SONiC switch to interconnect two IPv6-only customer networks. The engineer must configure Ethernet 1/3 with a global unicast address 2001:db8:1:1::1/64 and ensure that the interface can automatically generate its link-local address for neighbor discovery. After configuring the global address, the engineer wants to verify that both addresses are present on the interface. Which command accomplishes this?
Select an answer first
4application · medium
A network architect is planning the deployment of a Dell SONiC switch as a core router. The architect needs to connect multiple transit networks, each on a different subnet, using a single physical interface to conserve ports. What is the most appropriate way to achieve this?
Select an answer first
5application · easy
A network engineer is verifying the configuration of a Dell SONiC switch after a recent change. The engineer wants to see a summary of all Ethernet interfaces that have IP addresses assigned, along with their operational status, in a single view. Which command provides this information?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to SONIC-DEPLOY

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Dell Technologies. “SONIC-DEPLOY” is a trademark of its owner, used for identification only.

Administer L3 IP Addressing on Ethernet Ports SONIC-DEPLOY Practice Questions (Page 1)

Questions 1–5

Which SONiC command shows the operational state (up/down) of an Ethernet interface?

A network architect is planning the deployment of a Dell SONiC switch as a core router. The architect needs to connect multiple transit networks, each on a different subnet, using a single physical interface to conserve ports. What is the most appropriate way to achieve this?

A network engineer is verifying the configuration of a Dell SONiC switch after a recent change. The engineer wants to see a summary of all Ethernet interfaces that have IP addresses assigned, along with their operational status, in a single view. Which command provides this information?

Keep studying — Routing