A network engineer is troubleshooting a Cisco router that is not routing traffic between two VLANs. The 'show ip interface brief' output shows both VLAN interfaces are 'up/up'. However, the 'show running-config' output shows that the 'ip routing' command is missing. What is the most likely cause of the routing failure?

The physical switch ports are not configured as trunk ports.

Inter-VLAN routing is disabled on the router.

The VLAN interfaces are not assigned IP addresses.

The router's CPU is overloaded.

A technician is at a remote site and needs to quickly determine if a Cisco router has lost power or is simply rebooting. The technician does not have console access. Which physical indicator should the technician observe to make this determination?

The RPS (Redundant Power Supply) LED

The link LEDs on the Ethernet ports

A technician is verifying the health of a Cisco router's memory and CPU. The technician needs to see the current memory utilization and the CPU usage of the router. Which two commands should the technician run to capture this status?

show interfaces and show ip route

show version and show running-config

show memory and show processes cpu

show logging and show inventory

A field technician is standing in front of a Cisco Catalyst switch that is not passing traffic. The technician notices that the system LED is solid amber, but the port LEDs for the connected devices are green. Based on the LED status, what is the most likely conclusion about the switch's operational state?

The switch has a hardware or power supply fault, even though the individual ports may still be operational.

The switch is in the middle of a software upgrade and will return to normal shortly.

The switch has lost its running configuration and is running with factory defaults.

The switch is functioning normally, but the connected devices are powered off.

CiscoCertified Field Technician (CCT)

Domain 2Objective 7

2.7 Describe How to Capture Device Status 800-150 Practice Questions (Page 4)

Part of the 2.0 Common Service Tasks and Tools domain, which accounts for 15% of the 800-150 exam. Cisco does not publish an official question count, but from its 120-minute exam (~50–80 total, ~8–12 in this domain), expect 1–1 from this objective — we provide 23 practice questions to prepare you well beyond it. (estimate)

23questions here

5free pages

4concepts

15%of the exam

Questions 16–20

16expert · hard
A network engineer is troubleshooting a Cisco router that is not routing traffic between two VLANs. The 'show ip interface brief' output shows both VLAN interfaces are 'up/up'. However, the 'show running-config' output shows that the 'ip routing' command is missing. What is the most likely cause of the routing failure?
Select an answer first
17application · easy
A technician is at a remote site and needs to quickly determine if a Cisco router has lost power or is simply rebooting. The technician does not have console access. Which physical indicator should the technician observe to make this determination?
Select an answer first
18application · medium
A technician is verifying the health of a Cisco router's memory and CPU. The technician needs to see the current memory utilization and the CPU usage of the router. Which two commands should the technician run to capture this status?
Select an answer first
19application · medium
A field technician is standing in front of a Cisco Catalyst switch that is not passing traffic. The technician notices that the system LED is solid amber, but the port LEDs for the connected devices are green. Based on the LED status, what is the most likely conclusion about the switch's operational state?
Select an answer first
20application · easy
A network engineer is verifying that a newly installed Cisco router has the correct amount of memory and the expected IOS version. Which single CLI command provides all of this information in one output?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to 800-150

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Cisco. “800-150” is a trademark of its owner, used for identification only.

2.7 Describe How to Capture Device Status 800-150 Practice Questions (Page 4)

Questions 16–20

A technician is at a remote site and needs to quickly determine if a Cisco router has lost power or is simply rebooting. The technician does not have console access. Which physical indicator should the technician observe to make this determination?

A technician is verifying the health of a Cisco router's memory and CPU. The technician needs to see the current memory utilization and the CPU usage of the router. Which two commands should the technician run to capture this status?

A network engineer is verifying that a newly installed Cisco router has the correct amount of memory and the expected IOS version. Which single CLI command provides all of this information in one output?

Keep studying — 2.0 Common Service Tasks and Tools