A technician is troubleshooting a console connection to a Cisco switch. The technician has verified the cable and COM port are correct, but the terminal emulator shows garbled characters. The switch is known to have been configured with a non-default baud rate. What should the technician do?

Try different baud rates until the output is readable

Change the data bits to 7 and parity to even

Use a different terminal emulator

Reboot the switch to reset the baud rate to default

What indicates that a console session has been successfully established with a Cisco device?

The laptop's Wi-Fi connects to the device

The device's LEDs blink rapidly

The device's power LED turns green

The device's CLI prompt appears (e.g., 'Switch>')

A technician is using Tera Term to connect to a Cisco router console. The technician has set the baud rate to 9600, data bits to 8, parity to none, stop bits to 1, and flow control to none. The session works, but the technician notices that the router's console port is configured with a different baud rate. What is the most likely result?

The session will be slower but still work

The session will work normally because Tera Term auto-negotiates

The session will produce garbled output or no output

The session will disconnect after a few seconds

What is the primary purpose of terminal emulation software like Tera Term in a console session?

To create a backup of the device's configuration

To emulate a terminal and provide a CLI interface to the device

To configure network routing protocols

To monitor network traffic in real time

A technician is using Tera Term to connect to a Cisco router console. The technician selects the correct COM port and sets the baud rate to 9600. After pressing Enter, the technician sees 'Router>' prompt. What should the technician do next to access privileged EXEC mode?

Type 'configure terminal' and press Enter

Type 'show running-config' and press Enter

CiscoCertified Field Technician (CCT)

Domain 2Objective 6

2.6 Explain How to Connect to the Console Port 800-150 Practice Questions (Page 1)

Part of the 2.0 Common Service Tasks and Tools domain, which accounts for 15% of the 800-150 exam. Cisco does not publish an official question count, but from its 120-minute exam (~50–80 total, ~8–12 in this domain), expect 1–1 from this objective — we provide 18 practice questions to prepare you well beyond it. (estimate)

18questions here

4free pages

5concepts

15%of the exam

Questions 1–5

1expert · hard
A technician is troubleshooting a console connection to a Cisco switch. The technician has verified the cable and COM port are correct, but the terminal emulator shows garbled characters. The switch is known to have been configured with a non-default baud rate. What should the technician do?
Select an answer first
2foundation · easy
What indicates that a console session has been successfully established with a Cisco device?
Select an answer first
3expert · medium
A technician is using Tera Term to connect to a Cisco router console. The technician has set the baud rate to 9600, data bits to 8, parity to none, stop bits to 1, and flow control to none. The session works, but the technician notices that the router's console port is configured with a different baud rate. What is the most likely result?
Select an answer first
4foundation · easy
What is the primary purpose of terminal emulation software like Tera Term in a console session?
Select an answer first
5application · easy
A technician is using Tera Term to connect to a Cisco router console. The technician selects the correct COM port and sets the baud rate to 9600. After pressing Enter, the technician sees 'Router>' prompt. What should the technician do next to access privileged EXEC mode?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to 800-150

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Cisco. “800-150” is a trademark of its owner, used for identification only.