A network engineer is verifying EVPN route exchange between two Dell SONiC leaf switches that are configured for asymmetric IRB. The engineer notices that MAC/IP advertisement routes (Type-2) are being exchanged, but IP prefix routes (Type-5) are not. What is the most likely reason for the missing Type-5 routes?

The `advertise ipv4 unicast` option is not enabled under the EVPN address family.

The VNI for the tenant VLAN is not mapped to a VXLAN interface.

The BGP EVPN peer is not configured as a route reflector.

The `advertise-all-vni` option is not enabled under the EVPN address family.

A data center team is deploying BGP EVPN on Dell SONiC leaf switches to provide VXLAN-based Layer 2 and Layer 3 services. They have configured the VXLAN tunnels and VLAN-to-VNI mappings on all leafs. However, the EVPN address family is not yet enabled in BGP. Which configuration step is required to enable the EVPN control plane?

Configure `address-family evpn` under the BGP neighbor and activate it.

Create a route-map that matches EVPN route types and apply it to the BGP neighbor.

Enable `route-reflector-client` on the BGP neighbor to propagate EVPN routes.

Set `network command` under BGP to advertise the VXLAN VNI subnets.

Dell SONiC Deploy

Domain 5Objective 3

Configure and Verify BGP EVPN with Asymmetric IRB SONIC-DEPLOY Practice Questions (Page 3)

Part of the VXLAN domain, which accounts for 16% of the SONIC-DEPLOY exam.

24questions here

5free pages

7concepts

16%of the exam

Questions 11–15

11application · medium
After configuring BGP EVPN with asymmetric IRB on Dell SONiC, an engineer wants to verify that MAC addresses learned from a remote VTEP are being populated correctly. Which command should they use to check the EVPN MAC table?
Select an answer first
12foundation · easy
Which Dell SONiC command displays the BGP EVPN peers and their state?
Select an answer first
13foundation · easy
In Dell SONiC, which address family must be activated under the BGP neighbor configuration to exchange EVPN routes for VXLAN control plane?
Select an answer first
14application · medium
A network engineer is verifying EVPN route exchange between two Dell SONiC leaf switches that are configured for asymmetric IRB. The engineer notices that MAC/IP advertisement routes (Type-2) are being exchanged, but IP prefix routes (Type-5) are not. What is the most likely reason for the missing Type-5 routes?
Select an answer first
15application · medium
A data center team is deploying BGP EVPN on Dell SONiC leaf switches to provide VXLAN-based Layer 2 and Layer 3 services. They have configured the VXLAN tunnels and VLAN-to-VNI mappings on all leafs. However, the EVPN address family is not yet enabled in BGP. Which configuration step is required to enable the EVPN control plane?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to SONIC-DEPLOY

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Dell Technologies. “SONIC-DEPLOY” is a trademark of its owner, used for identification only.

Configure and Verify BGP EVPN with Asymmetric IRB SONIC-DEPLOY Practice Questions (Page 3)

Questions 11–15

After configuring BGP EVPN with asymmetric IRB on Dell SONiC, an engineer wants to verify that MAC addresses learned from a remote VTEP are being populated correctly. Which command should they use to check the EVPN MAC table?

Which Dell SONiC command displays the BGP EVPN peers and their state?

In Dell SONiC, which address family must be activated under the BGP neighbor configuration to exchange EVPN routes for VXLAN control plane?

Keep studying — VXLAN