A network engineer unboxes a new Dell switch in a server room. The switch has no configuration, and the engineer needs to access the CLI to begin initial setup. The engineer has a laptop with a USB-to-RJ45 console cable and a terminal emulator. Which action should the engineer take FIRST to establish a management session?

Power on the switch, wait for it to boot, and then use the 'ping' command from the laptop to discover the switch's IP address.

Connect an Ethernet cable from the laptop to any switch port and use a web browser to access the default IP address 192.168.1.1.

Connect the console cable to the switch's console port and the laptop, then open a terminal emulator with the correct COM port and settings (e.g., 9600 baud, 8-N-1).

Assign a management IP address to the switch using the front-panel buttons, then connect via SSH from the laptop.

A network admin is configuring a Dell switch for remote management. The switch has two VLANs: VLAN 1 (management) and VLAN 10 (data). The admin assigns the management IP 192.168.1.2/24 to VLAN 1 and enables SSH. The admin can ping the switch from a workstation on VLAN 10, but SSH fails. What is the MOST likely cause?

SSH is not enabled on the switch.

The switch's SSH server is not generating RSA keys, which are required for SSH.

The workstation is on a different VLAN and cannot reach the management VLAN.

The management IP is assigned to VLAN 1, but SSH is only listening on VLAN 10.

Dell Networking Foundations

Domain 1Objective 3

Describe the Steps and Settings Used for the Initial Configuration of a Switch NETWORKING-FOUNDATIONS Practice Questions (Page 4)

Part of the Networking Essentials domain, which accounts for 5% of the NETWORKING-FOUNDATIONS exam.

29questions here

6free pages

9concepts

5%of the exam

Questions 16–20

16application · medium
A network engineer unboxes a new Dell switch in a server room. The switch has no configuration, and the engineer needs to access the CLI to begin initial setup. The engineer has a laptop with a USB-to-RJ45 console cable and a terminal emulator. Which action should the engineer take FIRST to establish a management session?
Select an answer first
17foundation · easy
Which remote management protocol should be enabled for secure encrypted CLI access to a switch?
Select an answer first
18expert · hard
A network admin is configuring a Dell switch for remote management. The switch has two VLANs: VLAN 1 (management) and VLAN 10 (data). The admin assigns the management IP 192.168.1.2/24 to VLAN 1 and enables SSH. The admin can ping the switch from a workstation on VLAN 10, but SSH fails. What is the MOST likely cause?
Select an answer first
19foundation · easy
Which protocol is commonly used to establish a secure remote CLI session to a switch after it has been configured with an IP address?
Select an answer first
20application · medium
A network admin is configuring a Dell switch remotely. The admin has already configured a management IP and a local user account. The admin wants to establish a secure CLI session from a Linux workstation. Which command should the admin use on the workstation?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to NETWORKING-FOUNDATIONS

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Dell Technologies. “NETWORKING-FOUNDATIONS” is a trademark of its owner, used for identification only.

Describe the Steps and Settings Used for the Initial Configuration of a Switch NETWORKING-FOUNDATIONS Practice Questions (Page 4)

Questions 16–20

Which remote management protocol should be enabled for secure encrypted CLI access to a switch?

Which protocol is commonly used to establish a secure remote CLI session to a switch after it has been configured with an IP address?

A network admin is configuring a Dell switch remotely. The admin has already configured a management IP and a local user account. The admin wants to establish a secure CLI session from a Linux workstation. Which command should the admin use on the workstation?

Keep studying — Networking Essentials