A security audit recommends that no user devices be placed in the default VLAN. An administrator is configuring a new access switch. Which action BEST satisfies this recommendation?

Create a new VLAN and use it as the native VLAN on trunks.

Assign all user access ports to a VLAN other than VLAN 1, such as VLAN 100.

Disable trunking on all ports and use only access ports.

Change the native VLAN on all trunk ports to VLAN 1.

A Layer 3 switch has VLANs 10 and 20 configured. The engineer creates SVIs for both VLANs and assigns IP addresses 192.168.10.1/24 and 192.168.20.1/24. Hosts in VLAN 10 can ping the SVI for VLAN 10, and hosts in VLAN 20 can ping the SVI for VLAN 20. However, hosts in VLAN 10 cannot ping hosts in VLAN 20. What is the most likely missing configuration?

Create a VLAN interface for each VLAN and assign it to the access ports

Assign IP addresses to the physical ports in each VLAN

Enable IP routing on the switch with 'ip routing'

Configure a trunk port between the switch and a router

How does 802.1Q tagging allow multiple VLANs to traverse a single trunk link between switches?

By encapsulating the entire Ethernet frame in an IP header

By assigning a different IP subnet to each VLAN on the trunk

By inserting a 4-byte tag into the Ethernet frame that identifies the VLAN

By using the source MAC address to determine the VLAN

CiscoCertified Network Associate (CCNA)

Domain 2Objective 1

2.1 Configure and Verify VLANs (normal Range) Spanning Multiple Switches 200-301 Practice Questions (Page 5)

Part of the Network Access domain, which accounts for 20% of the 200-301 exam. Cisco does not publish an official question count, but from its 120-minute exam (~50–80 total, ~10–16 in this domain), expect 1–2 from this objective — we provide 32 practice questions to prepare you well beyond it. (estimate)

32questions here

7free pages

8concepts

20%of the exam

Questions 21–25

21foundation · easy
What is the default VLAN on a Cisco switch?
Select an answer first
22application · easy
An administrator is configuring a new switch port for a printer that should be in VLAN 30. The port is currently in default configuration. The administrator enters the following commands: 'interface GigabitEthernet0/1', 'switchport mode access', 'switchport access vlan 30'. The printer is connected and receives an IP address from the DHCP server in VLAN 30. Which additional verification command would confirm the port is correctly assigned?
Select an answer first
23application · medium
A security audit recommends that no user devices be placed in the default VLAN. An administrator is configuring a new access switch. Which action BEST satisfies this recommendation?
Select an answer first
24application · medium
A Layer 3 switch has VLANs 10 and 20 configured. The engineer creates SVIs for both VLANs and assigns IP addresses 192.168.10.1/24 and 192.168.20.1/24. Hosts in VLAN 10 can ping the SVI for VLAN 10, and hosts in VLAN 20 can ping the SVI for VLAN 20. However, hosts in VLAN 10 cannot ping hosts in VLAN 20. What is the most likely missing configuration?
Select an answer first
25foundation · easy
How does 802.1Q tagging allow multiple VLANs to traverse a single trunk link between switches?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to 200-301

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Cisco. “200-301” is a trademark of its owner, used for identification only.

2.1 Configure and Verify VLANs (normal Range) Spanning Multiple Switches 200-301 Practice Questions (Page 5)

Questions 21–25

What is the default VLAN on a Cisco switch?

A security audit recommends that no user devices be placed in the default VLAN. An administrator is configuring a new access switch. Which action BEST satisfies this recommendation?

How does 802.1Q tagging allow multiple VLANs to traverse a single trunk link between switches?

Keep studying — Network Access