A network admin is configuring a switch port for a new IP phone. The phone will be in VLAN 20 for voice, and the PC connected to the phone will be in VLAN 10 for data. The admin enters the following commands: 'interface gigabitethernet0/1', 'switchport mode access', 'switchport access vlan 10', 'switchport voice vlan 20'. Which command would verify that the voice VLAN is correctly configured?

show running-config interface gigabitethernet0/1

What is a Switch Virtual Interface (SVI) on a Layer 3 switch?

A physical interface that connects to a router

A virtual interface that provides an IP address for a VLAN and enables routing between VLANs

A management interface used only for SSH access

A trunk interface that carries multiple VLANs

A router is connected to a switch via a single Ethernet link. The network has VLAN 10 and VLAN 20, and hosts in these VLANs need to communicate. The switch port is configured as a trunk. Which router configuration enables interVLAN routing?

Create VLAN interfaces on the router and assign them to the switch trunk.

Assign two IP addresses to the physical interface Gi0/0, one in each VLAN subnet.

Configure the router's Gi0/0 as a trunk port with 'switchport mode trunk'.

Create subinterfaces Gi0/0.10 and Gi0/0.20 with encapsulation dot1Q 10 and 20, and assign IP addresses in each VLAN's subnet.

CiscoCertified Network Associate (CCNA)

Domain 2Objective 1

2.1 Configure and Verify VLANs (normal Range) Spanning Multiple Switches 200-301 Practice Questions (Page 2)

Part of the Network Access domain, which accounts for 20% of the 200-301 exam. Cisco does not publish an official question count, but from its 120-minute exam (~50–80 total, ~10–16 in this domain), expect 1–2 from this objective — we provide 32 practice questions to prepare you well beyond it. (estimate)

32questions here

7free pages

8concepts

20%of the exam

Questions 6–10

6application · medium
A network admin is configuring a switch port for a new IP phone. The phone will be in VLAN 20 for voice, and the PC connected to the phone will be in VLAN 10 for data. The admin enters the following commands: 'interface gigabitethernet0/1', 'switchport mode access', 'switchport access vlan 10', 'switchport voice vlan 20'. Which command would verify that the voice VLAN is correctly configured?
Select an answer first
7foundation · easy
Which command displays a summary of all VLANs on a switch, including their names and status?
Select an answer first
8foundation · easy
What is a Switch Virtual Interface (SVI) on a Layer 3 switch?
Select an answer first
9application · medium
A router is connected to a switch via a single Ethernet link. The network has VLAN 10 and VLAN 20, and hosts in these VLANs need to communicate. The switch port is configured as a trunk. Which router configuration enables interVLAN routing?
Select an answer first
10foundation · easy
Which command enables IP routing on a Layer 3 switch?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to 200-301

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Cisco. “200-301” is a trademark of its owner, used for identification only.

2.1 Configure and Verify VLANs (normal Range) Spanning Multiple Switches 200-301 Practice Questions (Page 2)

Questions 6–10

Which command displays a summary of all VLANs on a switch, including their names and status?

What is a Switch Virtual Interface (SVI) on a Layer 3 switch?

A router is connected to a switch via a single Ethernet link. The network has VLAN 10 and VLAN 20, and hosts in these VLANs need to communicate. The switch port is configured as a trunk. Which router configuration enables interVLAN routing?

Which command enables IP routing on a Layer 3 switch?

Keep studying — Network Access