A router has a default route via 203.0.113.1 (AD 1) and a floating default route via 198.51.100.1 (AD 200). The primary default route is removed because the next-hop becomes unreachable. What will the router do?

Keep the primary default route in the routing table until the next-hop recovers.

Load-balance traffic between the two default routes.

Install the floating default route via 198.51.100.1 if that next-hop is reachable.

Remove both default routes from the routing table.

A network engineer is troubleshooting an IPv6 connectivity issue. The router has the following configuration: ipv6 route 2001:db8:10::/64 2001:db8:1::1 ipv6 route 2001:db8:10::/64 GigabitEthernet0/0 The engineer wants to verify which route is active. Which command will show the active route and its administrative distance?

show ipv6 route 2001:db8:10::/64

show running-config | include ipv6 route

What is a key difference between the IPv4 and IPv6 static route commands on Cisco IOS?

IPv6 static routes do not support administrative distance

IPv6 uses a prefix length (e.g., /64) while IPv4 uses a subnet mask (e.g., 255.255.255.0)

IPv6 static routes cannot use a next-hop address; they must use an exit interface

IPv4 static routes use the 'ipv4 route' command, while IPv6 uses 'ipv6 route'

CiscoCertified Network Associate (CCNA)

Domain 3Objective 3

3.3 Configure and Verify IPv4 and IPv6 Static Routing 200-301 Practice Questions (Page 3)

Part of the IP Connectivity domain, which accounts for 25% of the 200-301 exam. Cisco does not publish an official question count, but from its 120-minute exam (~50–80 total, ~13–20 in this domain), expect 3–4 from this objective — we provide 14 practice questions to prepare you well beyond it. (estimate)

14questions here

3free pages

6concepts

25%of the exam

Questions 11–14

11expert · hard
A router has a default route via 203.0.113.1 (AD 1) and a floating default route via 198.51.100.1 (AD 200). The primary default route is removed because the next-hop becomes unreachable. What will the router do?
Select an answer first
12expert · medium
A network engineer is troubleshooting an IPv6 connectivity issue. The router has the following configuration: ipv6 route 2001:db8:10::/64 2001:db8:1::1 ipv6 route 2001:db8:10::/64 GigabitEthernet0/0 The engineer wants to verify which route is active. Which command will show the active route and its administrative distance?
Select an answer first
13foundation · medium
What is a key difference between the IPv4 and IPv6 static route commands on Cisco IOS?
Select an answer first
14foundation · medium
An administrator configured an IPv6 static route and wants to verify that it is present in the routing table. Which command should be used?
Select an answer first

Finished these 4 questions?

Review the revealed explanations, or continue through the curriculum.

No more pagesBack to 200-301

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Cisco. “200-301” is a trademark of its owner, used for identification only.

3.3 Configure and Verify IPv4 and IPv6 Static Routing 200-301 Practice Questions (Page 3)

Questions 11–14

A router has a default route via 203.0.113.1 (AD 1) and a floating default route via 198.51.100.1 (AD 200). The primary default route is removed because the next-hop becomes unreachable. What will the router do?

What is a key difference between the IPv4 and IPv6 static route commands on Cisco IOS?

An administrator configured an IPv6 static route and wants to verify that it is present in the routing table. Which command should be used?

Keep studying — IP Connectivity