A router has a primary route to 10.0.0.0/8 via 192.168.1.1 and a floating static route to the same network via 192.168.2.1 with AD 200. The administrator notices that the floating route is NOT appearing in the routing table even after the primary link goes down. What is the most likely reason?

The floating route was configured with the wrong next-hop address.

The floating route has an administrative distance that is too low.

The router does not support floating static routes.

The primary route is still in the routing table because the interface did not go down.

Which IPv6 command configures a default static route that sends all unmatched traffic to the next-hop address 2001:db8:1::1?

ipv6 route ::/128 2001:db8:1::1

ipv6 route 0::0/0 2001:db8:1::1

You have two static routes to 10.10.0.0/16: one via 192.168.1.1 (AD 1) and one via 192.168.2.1 (AD 200). The route via 192.168.1.1 is removed from the routing table because the next-hop becomes unreachable. What will the router do?

Load-balance traffic between the two routes.

Install the route via 192.168.2.1 in the routing table.

Remove both routes from the routing table.

Keep the route via 192.168.1.1 in the routing table until the next-hop recovers.

A router has a static route to 10.20.0.0/16 via 10.0.0.1 and a floating static route to the same network via 10.0.0.2 with AD 150. The administrator wants to verify that the floating route is currently in the routing table. Which command output would confirm this?

show running-config | include 10.20.0.0

CiscoCertified Network Associate (CCNA)

Domain 3Objective 3

3.3 Configure and Verify IPv4 and IPv6 Static Routing 200-301 Practice Questions (Page 1)

Part of the IP Connectivity domain, which accounts for 25% of the 200-301 exam. Cisco does not publish an official question count, but from its 120-minute exam (~50–80 total, ~13–20 in this domain), expect 3–4 from this objective — we provide 14 practice questions to prepare you well beyond it. (estimate)

14questions here

3free pages

6concepts

25%of the exam

Questions 1–5

1expert · medium
A router has a primary route to 10.0.0.0/8 via 192.168.1.1 and a floating static route to the same network via 192.168.2.1 with AD 200. The administrator notices that the floating route is NOT appearing in the routing table even after the primary link goes down. What is the most likely reason?
Select an answer first
2foundation · medium
Which IPv6 command configures a default static route that sends all unmatched traffic to the next-hop address 2001:db8:1::1?
Select an answer first
3foundation · medium
Which command displays the IPv4 routing table, including static routes and their administrative distances?
Select an answer first
4expert · hard
You have two static routes to 10.10.0.0/16: one via 192.168.1.1 (AD 1) and one via 192.168.2.1 (AD 200). The route via 192.168.1.1 is removed from the routing table because the next-hop becomes unreachable. What will the router do?
Select an answer first
5application · easy
A router has a static route to 10.20.0.0/16 via 10.0.0.1 and a floating static route to the same network via 10.0.0.2 with AD 150. The administrator wants to verify that the floating route is currently in the routing table. Which command output would confirm this?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to 200-301

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Cisco. “200-301” is a trademark of its owner, used for identification only.