A network administrator needs to verify that a specific route is being used for forwarding on a Junos device. The route is a static route to 172.16.0.0/16 with a next hop of 192.168.1.1. Which command will show whether this route is installed in the forwarding table?

show configuration routing-options static

show route forwarding-table destination 172.16.0.0/16

A network engineer is explaining the difference between the routing table and the forwarding table to a new team member. Which statement accurately describes the relationship between the two tables?

The routing table is used for packet forwarding, while the forwarding table is used for route selection.

The forwarding table is derived from the active routes in the routing table and is used for packet forwarding.

Both tables are identical and contain the same information.

The routing table contains only active routes, while the forwarding table contains all learned routes.

A network engineer is analyzing the routing table on a Junos device and sees the following entry for 10.0.0.0/24: 'OSPF Preference: 10, Metric: 100, Next hop: 192.168.1.1'. The engineer wants to know why this route is active even though there is also a static route to 10.0.0.0/24 with a preference of 5. What should the engineer check first?

The status of the static route in the routing table.

The metric of the static route.

The next hop of the OSPF route.

A Junos device has two routes to the same destination: one learned via OSPF (preference 10) and one via Static (preference 5). Which route becomes active?

The static route, because it has a lower preference value.

Both routes become active, and traffic is load-balanced between them.

The OSPF route, because OSPF is a dynamic protocol and is more trusted.

The OSPF route, because it has a higher preference value, indicating a more reliable route.

A network engineer is analyzing the routing table on a Junos device and sees the following entry for 10.0.0.0/8: 'OSPF Preference: 10, Metric: 100, Next hop: 192.168.1.1'. The engineer also sees a static route to 10.0.0.0/8 with a preference of 5 and a metric of 50, but the static route is marked as 'inactive'. What is the most likely reason for the static route being inactive?

The static route's next hop is unreachable.

The OSPF route has a lower preference.

The static route has a higher preference.

The OSPF route has a lower metric.

Juniper NetworksCertified Associate, Junos

Domain 6Objective 2

Routing and Forwarding Tables JN0-105 Practice Questions (Page 2)

Part of the Routing Fundamentals domain, which makes up ~13% of our current practice bank. Juniper Networks does not publish an official question count, but from its 90-minute exam (~35–60 total, ~5–8 in this domain), expect 1–1 from this objective — we provide 14 practice questions to prepare you well beyond it. (estimate)

14questions here

3free pages

5concepts

Questions 6–10

6application · medium
A network administrator needs to verify that a specific route is being used for forwarding on a Junos device. The route is a static route to 172.16.0.0/16 with a next hop of 192.168.1.1. Which command will show whether this route is installed in the forwarding table?
Select an answer first
7application · medium
A network engineer is explaining the difference between the routing table and the forwarding table to a new team member. Which statement accurately describes the relationship between the two tables?
Select an answer first
8application · medium
A network engineer is analyzing the routing table on a Junos device and sees the following entry for 10.0.0.0/24: 'OSPF Preference: 10, Metric: 100, Next hop: 192.168.1.1'. The engineer wants to know why this route is active even though there is also a static route to 10.0.0.0/24 with a preference of 5. What should the engineer check first?
Select an answer first
9foundation · medium
A Junos device has two routes to the same destination: one learned via OSPF (preference 10) and one via Static (preference 5). Which route becomes active?
Select an answer first
10expert · hard
A network engineer is analyzing the routing table on a Junos device and sees the following entry for 10.0.0.0/8: 'OSPF Preference: 10, Metric: 100, Next hop: 192.168.1.1'. The engineer also sees a static route to 10.0.0.0/8 with a preference of 5 and a metric of 50, but the static route is marked as 'inactive'. What is the most likely reason for the static route being inactive?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to JN0-105

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Juniper Networks. “JN0-105” is a trademark of its owner, used for identification only.

Routing and Forwarding Tables JN0-105 Practice Questions (Page 2)

Questions 6–10

A network administrator needs to verify that a specific route is being used for forwarding on a Junos device. The route is a static route to 172.16.0.0/16 with a next hop of 192.168.1.1. Which command will show whether this route is installed in the forwarding table?

A network engineer is explaining the difference between the routing table and the forwarding table to a new team member. Which statement accurately describes the relationship between the two tables?

A Junos device has two routes to the same destination: one learned via OSPF (preference 10) and one via Static (preference 5). Which route becomes active?

Keep studying — Routing Fundamentals