An administrator is troubleshooting a connectivity issue in an MX7000. A compute sled is not receiving network traffic, but other sleds on the same IOM are working. The IOM shows no errors in OMEM. What is the most likely cause?

The top-of-rack switch is down.

The IOM is in a degraded state.

The sled's mezzanine card is not connected to the IOM's fabric.

An MX7000 chassis has two 100GbE IOMs, each with two QSFP-DD ports. The network team wants to connect each IOM to two core switches for redundancy, but the core switches only have 25GbE SFP+ ports. They also want to maximize the number of active uplinks. What is the best configuration?

Use breakout cables on each QSFP-DD port to create four 25GbE links, and connect two links to each core switch.

Use both QSFP-DD ports with breakout cables to connect to the same core switch.

Use one QSFP-DD port to connect to each core switch using a single 100GbE link.

Use one QSFP-DD port with a breakout cable to connect to one core switch, and leave the other port unused.

An administrator notices that one of the IOMs in an MX7000 chassis is showing a degraded health status in OpenManage Enterprise Modular. What is the first step they should take to troubleshoot?

Immediately replace the IOM with a spare.

Check the physical cabling to the IOM.

Reboot the chassis to reset the IOM.

Review the IOM's event logs and health metrics in OMEM.

A company is planning to deploy an MX7000 with a mix of Ethernet and Fibre Channel workloads. They have a limited budget and want to minimize the number of IOMs. They need to support at least two Ethernet sleds and two Fibre Channel sleds, each with redundancy. What is the minimum number of IOMs required?

4 IOMs: two Ethernet and two Fibre Channel.

6 IOMs: three Ethernet and three Fibre Channel.

2 IOMs: one Ethernet and one Fibre Channel.

Dell PowerEdge MX Modular Deploy

Domain 1Objective 6

O Fabric POWEREDGE-MX-MODULAR-DEPLOY Practice Questions (Page 1)

Part of the MX-Series Features domain, which accounts for 27% of the POWEREDGE-MX-MODULAR-DEPLOY exam.

20questions here

4free pages

6concepts

27%of the exam

Questions 1–5

1expert · hard
An administrator is troubleshooting a connectivity issue in an MX7000. A compute sled is not receiving network traffic, but other sleds on the same IOM are working. The IOM shows no errors in OMEM. What is the most likely cause?
Select an answer first
2expert · hard
An MX7000 chassis has two 100GbE IOMs, each with two QSFP-DD ports. The network team wants to connect each IOM to two core switches for redundancy, but the core switches only have 25GbE SFP+ ports. They also want to maximize the number of active uplinks. What is the best configuration?
Select an answer first
3application · easy
An administrator notices that one of the IOMs in an MX7000 chassis is showing a degraded health status in OpenManage Enterprise Modular. What is the first step they should take to troubleshoot?
Select an answer first
4expert · hard
A company is planning to deploy an MX7000 with a mix of Ethernet and Fibre Channel workloads. They have a limited budget and want to minimize the number of IOMs. They need to support at least two Ethernet sleds and two Fibre Channel sleds, each with redundancy. What is the minimum number of IOMs required?
Select an answer first
5foundation · easy
Which of the following is a supported I/O module type in the Dell PowerEdge MX7000 chassis?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to POWEREDGE-MX-MODULAR-DEPLOY

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Dell Technologies. “POWEREDGE-MX-MODULAR-DEPLOY” is a trademark of its owner, used for identification only.

Describe Network Switches And/or I/O Fabric POWEREDGE-MX-MODULAR-DEPLOY Practice Questions (Page 1)

Questions 1–5

An administrator is troubleshooting a connectivity issue in an MX7000. A compute sled is not receiving network traffic, but other sleds on the same IOM are working. The IOM shows no errors in OMEM. What is the most likely cause?

An MX7000 chassis has two 100GbE IOMs, each with two QSFP-DD ports. The network team wants to connect each IOM to two core switches for redundancy, but the core switches only have 25GbE SFP+ ports. They also want to maximize the number of active uplinks. What is the best configuration?

An administrator notices that one of the IOMs in an MX7000 chassis is showing a degraded health status in OpenManage Enterprise Modular. What is the first step they should take to troubleshoot?

Which of the following is a supported I/O module type in the Dell PowerEdge MX7000 chassis?

Keep studying — MX-Series Features