An engineer configured an IP SLA UDP jitter operation to monitor VoIP quality between two sites. The operation is scheduled and running, but 'show ip sla statistics' shows a return code of 4 (timeout) for every probe. The engineer confirms that the destination router is reachable via ping and that the UDP port is open. What is the most likely cause of the timeouts?

The destination router does not have a responder configured for IP SLA UDP jitter.

The source router is using the wrong source interface.

The frequency is set too high, causing the probes to be dropped.

The IP SLA operation is not scheduled correctly.

What is the purpose of the 'frequency' command in IP SLA configuration?

To set the time of day when the operation starts

To set the duration of the IP SLA operation

To set how often the IP SLA probe is sent

To set the number of probes to send in each operation

What is the purpose of configuring IP SLA tracking?

To store IP SLA results in a database for historical analysis

To influence routing decisions based on the performance of the IP SLA operation

To provide real-time monitoring of IP SLA results through SNMP

To automatically adjust the frequency of IP SLA probes based on network conditions

An engineer must measure one-way delay between two Cisco routers. The engineer has configured an IP SLA UDP jitter operation on the source router. What additional configuration is required on the destination router to ensure accurate one-way delay measurements?

Enable NetFlow on the destination router.

Configure a loopback interface on the destination router.

Enable the IP SLA responder on the destination router.

Configure a static route back to the source router.

CiscoCertified Network Professional Enterprise

Domain 4Objective 4

4.4 Configure and Verify IPSLA 350-401 Practice Questions (Page 3)

Part of the 4.0 Network Assurance domain, which accounts for 10% of the 350-401 exam. Cisco does not publish an official question count, but from its 120-minute exam (~50–80 total, ~5–8 in this domain), expect 1–1 from this objective — we provide 21 practice questions to prepare you well beyond it. (estimate)

21questions here

5free pages

5concepts

10%of the exam

Questions 11–15

11expert · hard
An engineer must measure the response time of a database application that uses TCP port 1433. The database server is not a Cisco device. Which IP SLA operation type should be used?
Select an answer first
12expert · hard
An engineer configured an IP SLA UDP jitter operation to monitor VoIP quality between two sites. The operation is scheduled and running, but 'show ip sla statistics' shows a return code of 4 (timeout) for every probe. The engineer confirms that the destination router is reachable via ping and that the UDP port is open. What is the most likely cause of the timeouts?
Select an answer first
13foundation · easy
What is the purpose of the 'frequency' command in IP SLA configuration?
Select an answer first
14foundation · easy
What is the purpose of configuring IP SLA tracking?
Select an answer first
15expert · hard
An engineer must measure one-way delay between two Cisco routers. The engineer has configured an IP SLA UDP jitter operation on the source router. What additional configuration is required on the destination router to ensure accurate one-way delay measurements?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to 350-401

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Cisco. “350-401” is a trademark of its owner, used for identification only.

4.4 Configure and Verify IPSLA 350-401 Practice Questions (Page 3)

Questions 11–15

An engineer must measure the response time of a database application that uses TCP port 1433. The database server is not a Cisco device. Which IP SLA operation type should be used?

What is the purpose of the 'frequency' command in IP SLA configuration?

What is the purpose of configuring IP SLA tracking?

An engineer must measure one-way delay between two Cisco routers. The engineer has configured an IP SLA UDP jitter operation on the source router. What additional configuration is required on the destination router to ensure accurate one-way delay measurements?

Keep studying — 4.0 Network Assurance