A FortiGate is used to connect two enterprise sites via iBGP. The administrator wants to ensure that when a route is advertised from one site to the other, the next hop is set to the FortiGate's own address. Which configuration should be applied?

Set next-hop-self under the BGP neighbor configuration.

Set the local preference to a higher value.

Configure the neighbor with a different remote-as.

Use a route map to set the MED attribute.

A FortiGate is not advertising a route to a BGP peer, even though the route is present in the routing table. The administrator has verified that the prefix list applied outbound permits the route. What is the next most likely cause to investigate?

The route was not originated into BGP via a network statement or redistribute command.

The BGP session is in the Established state.

The route has a high MED value.

A FortiGate BGP neighbor is stuck in the Active state. The administrator has verified that the IP address and remote AS are correct. What is the most likely cause of this issue?

The neighbor is not reachable due to a firewall policy or routing issue.

The BGP holdtime is set too low.

The neighbor is configured with a different AS number.

FortinetNSE 7 - Enterprise Firewall Administrator

Domain 4Objective 2

Implement BGP to Route Enterprise Traffic NSE7-ENTERPRISE-FIREWALL-ADMINISTRATOR Practice Questions (Page 4)

Part of the Routing domain, which makes up ~13% of our current practice bank. Fortinet does not publish an official question count, but from its 70-minute exam (~30–45 total, ~4–6 in this domain), expect 2–3 from this objective — we provide 23 practice questions to prepare you well beyond it. (estimate)

23questions here

5free pages

6concepts

Questions 16–20

16application · medium
A FortiGate is used to connect two enterprise sites via iBGP. The administrator wants to ensure that when a route is advertised from one site to the other, the next hop is set to the FortiGate's own address. Which configuration should be applied?
Select an answer first
17expert · hard
A FortiGate is not advertising a route to a BGP peer, even though the route is present in the routing table. The administrator has verified that the prefix list applied outbound permits the route. What is the next most likely cause to investigate?
Select an answer first
18foundation · easy
Which BGP filtering method can be used to match routes based on the AS numbers in the AS path?
Select an answer first
19application · medium
A FortiGate BGP neighbor is stuck in the Active state. The administrator has verified that the IP address and remote AS are correct. What is the most likely cause of this issue?
Select an answer first
20foundation · easy
Which BGP filtering tool is used to match routes based on the IP prefix and prefix length?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to NSE7-ENTERPRISE-FIREWALL-ADMINISTRATOR

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Fortinet. “NSE7-ENTERPRISE-FIREWALL-ADMINISTRATOR” is a trademark of its owner, used for identification only.

Implement BGP to Route Enterprise Traffic NSE7-ENTERPRISE-FIREWALL-ADMINISTRATOR Practice Questions (Page 4)

Questions 16–20

A FortiGate is used to connect two enterprise sites via iBGP. The administrator wants to ensure that when a route is advertised from one site to the other, the next hop is set to the FortiGate's own address. Which configuration should be applied?

A FortiGate is not advertising a route to a BGP peer, even though the route is present in the routing table. The administrator has verified that the prefix list applied outbound permits the route. What is the next most likely cause to investigate?

Which BGP filtering method can be used to match routes based on the AS numbers in the AS path?

A FortiGate BGP neighbor is stuck in the Active state. The administrator has verified that the IP address and remote AS are correct. What is the most likely cause of this issue?

Which BGP filtering tool is used to match routes based on the IP prefix and prefix length?

Keep studying — Routing