A storage administrator is configuring a new Linux host to access a LUN on a Dell Unity array via iSCSI. The administrator has created a host object in Unisphere and added the host's IQN. However, the host cannot see the LUN. What is the most likely cause?

The host is not connected to the same IP subnet as the storage processor.

The host's iSCSI initiator is not running.

The LUN is not formatted with a filesystem.

The host's IQN was entered incorrectly in the host object.

A company is deploying a new application that requires multiple LUNs on a Dell Unity array. The application is critical and requires that if one LUN fails, the other LUNs remain available. The storage administrator wants to ensure that the LUNs are managed as a single unit for snapshots, but also wants to avoid a single point of failure. What should the administrator do?

Create a single large LUN to replace the multiple LUNs.

Create a host group and add all LUNs to it.

Create separate snapshots for each LUN without grouping them.

Create a consistency group for the LUNs and configure snapshots at the group level.

After configuring a new LUN and adding a Windows host to its ACL, the storage administrator wants to verify that the host can see and access the LUN. The host is connected via Fibre Channel. Which command should the administrator run on the Windows host to verify connectivity?

Run 'ping' to the storage processor's IP address.

Run 'fcping' to test the Fibre Channel path.

Run 'ipconfig' to check the IP address of the host.

Run 'diskpart' and list disks to see if the LUN appears.

Dell Unity Deploy

Domain 4Objective 4

Configure Host Access to Block Storage Resources UNITY-DEPLOY Practice Questions (Page 1)

Part of the Dell Unity XT and UnityVSA Storage Provisioning and Access domain, which accounts for 25% of the UNITY-DEPLOY exam.

24questions here

5free pages

6concepts

25%of the exam

Questions 1–5

1foundation · easy
Which command-line tool is commonly used on a Linux host to verify connectivity to an iSCSI target on Dell Unity?
Select an answer first
2application · medium
A storage administrator is configuring a new Linux host to access a LUN on a Dell Unity array via iSCSI. The administrator has created a host object in Unisphere and added the host's IQN. However, the host cannot see the LUN. What is the most likely cause?
Select an answer first
3foundation · easy
Which mechanism in Dell Unity controls which hosts can access a specific LUN?
Select an answer first
4expert · hard
A company is deploying a new application that requires multiple LUNs on a Dell Unity array. The application is critical and requires that if one LUN fails, the other LUNs remain available. The storage administrator wants to ensure that the LUNs are managed as a single unit for snapshots, but also wants to avoid a single point of failure. What should the administrator do?
Select an answer first
5application · medium
After configuring a new LUN and adding a Windows host to its ACL, the storage administrator wants to verify that the host can see and access the LUN. The host is connected via Fibre Channel. Which command should the administrator run on the Windows host to verify connectivity?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to UNITY-DEPLOY

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Dell Technologies. “UNITY-DEPLOY” is a trademark of its owner, used for identification only.

Configure Host Access to Block Storage Resources UNITY-DEPLOY Practice Questions (Page 1)

Questions 1–5

Which command-line tool is commonly used on a Linux host to verify connectivity to an iSCSI target on Dell Unity?

A storage administrator is configuring a new Linux host to access a LUN on a Dell Unity array via iSCSI. The administrator has created a host object in Unisphere and added the host's IQN. However, the host cannot see the LUN. What is the most likely cause?

Which mechanism in Dell Unity controls which hosts can access a specific LUN?

After configuring a new LUN and adding a Windows host to its ACL, the storage administrator wants to verify that the host can see and access the LUN. The host is connected via Fibre Channel. Which command should the administrator run on the Windows host to verify connectivity?

Keep studying — Dell Unity XT and UnityVSA Storage Provisioning and Access