An OS10 switch has a VRF named 'VRF-TENANT' with a VLAN interface (vlan200) assigned to it. The engineer needs to verify that the VRF is correctly routing traffic between two subnets that are both in VRF-TENANT. The engineer has verified that the VLAN interface is up and has IP addresses configured. Which command should be used to verify the routing table for VRF-TENANT?

show running-config vrf VRF-TENANT

A network engineer is configuring a new VRF on an OS10 switch. The VRF will be used for a customer that requires its own routing table. The engineer has already created the VRF with the command 'ip vrf CUSTOMER-A'. What is the next step to make the VRF operational?

Configure a default route in the VRF.

Reboot the switch to activate the VRF.

Assign at least one Layer 3 interface to the VRF using 'ip vrf forwarding'.

A service provider hosts multiple customers on a shared pair of OS10 switches in a data center. Each customer requires its own routing table to ensure that routes from one customer are never leaked to another. The provider also needs to support overlapping IP address spaces across customers. What is the primary reason to use VRF on these switches?

To create separate routing and forwarding tables for each customer, allowing overlapping IP addresses and preventing route leakage.

To provide redundancy by allowing multiple paths to the same destination.

To improve switching performance by reducing the size of the MAC address table.

To enable VLAN tagging across multiple switches for each customer.

Dell PowerSwitch Data Center Deploy

Domain 6Objective 1

VRF POWERSWITCH-DATA-CENTER-DEPLOY Practice Questions (Page 2)

Part of the Data Center Technologies domain, which accounts for 30% of the POWERSWITCH-DATA-CENTER-DEPLOY exam.

18questions here

4free pages

4concepts

30%of the exam

Questions 6–10

6expert · medium
An OS10 switch has a VRF named 'VRF-TENANT' with a VLAN interface (vlan200) assigned to it. The engineer needs to verify that the VRF is correctly routing traffic between two subnets that are both in VRF-TENANT. The engineer has verified that the VLAN interface is up and has IP addresses configured. Which command should be used to verify the routing table for VRF-TENANT?
Select an answer first
7application · easy
A network engineer is configuring a new VRF on an OS10 switch. The VRF will be used for a customer that requires its own routing table. The engineer has already created the VRF with the command 'ip vrf CUSTOMER-A'. What is the next step to make the VRF operational?
Select an answer first
8foundation · easy
Which show command displays the VRF instances configured on an OS10 switch?
Select an answer first
9application · easy
A service provider hosts multiple customers on a shared pair of OS10 switches in a data center. Each customer requires its own routing table to ensure that routes from one customer are never leaked to another. The provider also needs to support overlapping IP address spaces across customers. What is the primary reason to use VRF on these switches?
Select an answer first
10foundation · easy
To verify the routing table of a specific VRF named 'tenantA' on an OS10 switch, which command should you use?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to POWERSWITCH-DATA-CENTER-DEPLOY

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Dell Technologies. “POWERSWITCH-DATA-CENTER-DEPLOY” is a trademark of its owner, used for identification only.

VRF POWERSWITCH-DATA-CENTER-DEPLOY Practice Questions (Page 2)

Questions 6–10

A network engineer is configuring a new VRF on an OS10 switch. The VRF will be used for a customer that requires its own routing table. The engineer has already created the VRF with the command 'ip vrf CUSTOMER-A'. What is the next step to make the VRF operational?

Which show command displays the VRF instances configured on an OS10 switch?

To verify the routing table of a specific VRF named 'tenantA' on an OS10 switch, which command should you use?

Keep studying — Data Center Technologies