An engineer is troubleshooting an EIGRP neighbor that is stuck in the Init state. The engineer sees that hello packets are being received, but no updates are being exchanged. What is the most likely cause?

The hold timer is too short on the local router.

The reliable transport is not functioning because ACKs are not being sent.

The K-values are mismatched between the routers.

The router is configured as a stub and does not send updates.

A network engineer is migrating from classic EIGRP to named mode EIGRP. The engineer wants to configure EIGRP for IPv4 and IPv6 on the same router, with different metric weights per interface. What is the correct approach?

Configure named mode EIGRP with a single address-family that includes both IPv4 and IPv6, and set metric weights per interface.

Use classic EIGRP for IPv4 and named mode for IPv6, because named mode does not support IPv4.

Create a single named-mode EIGRP instance with two address-families, one for IPv4 and one for IPv6, and configure metric weights under each address-family.

Create two separate named-mode EIGRP instances, one for IPv4 and one for IPv6, and configure metric weights under each instance.

An engineer is designing an EIGRP network with multiple remote sites connected to a central hub. The engineer wants to reduce the number of queries sent to remote sites during a route failure. What should the engineer configure on the remote site routers?

Increase the hello timer on the remote site routers.

Set the variance command to a higher value on the remote site routers.

Disable automatic route summarization on the remote site routers.

Configure the remote site routers as EIGRP stub routers.

An engineer has two EIGRP paths to a destination. The successor has a feasible distance of 1000. The alternate path has a feasible distance of 2000. The engineer wants to use both paths for load balancing, but the alternate path is not currently used. What configuration will enable unequal-cost load balancing?

Set the K-values to include load and reliability.

Set variance to 2 on the router.

Set maximum-paths to 2 on the router.

Set the delay on the alternate path to match the successor.

A network engineer is configuring EIGRP stub routing on a remote site router that has only one connection to the rest of the network. The remote site has a LAN with multiple subnets. What is the best stub configuration to advertise the LAN subnets while preventing queries from being sent to the remote site?

Configure the router as a stub with the 'summary' keyword only.

Configure the router as a stub with the 'receive-only' keyword.

Configure the router as a stub with the 'connected' and 'static' keywords.

Configure the router as a stub with the 'leak-map' option.

CCIE Enterprise Infrastructure

Domain 1Objective 3

EIGRP CCIE-ENTERPRISE-INFRASTRUCTURE Practice Questions (Page 4)

Part of the Network Infrastructure domain, which accounts for 30% of the CCIE-ENTERPRISE-INFRASTRUCTURE exam. Cisco does not publish an official question count, but from its 120-minute exam (~50–80 total, ~15–24 in this domain), expect 3–4 from this objective — we provide 36 practice questions to prepare you well beyond it. (estimate)

36questions here

8free pages

15concepts

30%of the exam

Questions 16–20

16application · medium
An engineer is troubleshooting an EIGRP neighbor that is stuck in the Init state. The engineer sees that hello packets are being received, but no updates are being exchanged. What is the most likely cause?
Select an answer first
17application · medium
A network engineer is migrating from classic EIGRP to named mode EIGRP. The engineer wants to configure EIGRP for IPv4 and IPv6 on the same router, with different metric weights per interface. What is the correct approach?
Select an answer first
18application · medium
An engineer is designing an EIGRP network with multiple remote sites connected to a central hub. The engineer wants to reduce the number of queries sent to remote sites during a route failure. What should the engineer configure on the remote site routers?
Select an answer first
19application · medium
An engineer has two EIGRP paths to a destination. The successor has a feasible distance of 1000. The alternate path has a feasible distance of 2000. The engineer wants to use both paths for load balancing, but the alternate path is not currently used. What configuration will enable unequal-cost load balancing?
Select an answer first
20application · medium
A network engineer is configuring EIGRP stub routing on a remote site router that has only one connection to the rest of the network. The remote site has a LAN with multiple subnets. What is the best stub configuration to advertise the LAN subnets while preventing queries from being sent to the remote site?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to CCIE-ENTERPRISE-INFRASTRUCTURE

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Cisco. “CCIE-ENTERPRISE-INFRASTRUCTURE” is a trademark of its owner, used for identification only.

EIGRP CCIE-ENTERPRISE-INFRASTRUCTURE Practice Questions (Page 4)

Questions 16–20

An engineer is troubleshooting an EIGRP neighbor that is stuck in the Init state. The engineer sees that hello packets are being received, but no updates are being exchanged. What is the most likely cause?

A network engineer is migrating from classic EIGRP to named mode EIGRP. The engineer wants to configure EIGRP for IPv4 and IPv6 on the same router, with different metric weights per interface. What is the correct approach?

An engineer is designing an EIGRP network with multiple remote sites connected to a central hub. The engineer wants to reduce the number of queries sent to remote sites during a route failure. What should the engineer configure on the remote site routers?

Keep studying — Network Infrastructure