A router has two VRFs: 'BLUE' and 'GREEN'. A user in the BLUE VRF cannot reach a server that is directly connected to the GREEN VRF. The engineer confirms that both VRFs have correct routing tables and that the server's IP is reachable from the GREEN VRF. What is the most likely reason for the failure?

The router's global routing table is missing a static route.

The BLUE VRF's interface is administratively down.

The BLUE VRF has no route to the GREEN VRF's subnet, and route leaking is not configured.

The server's default gateway is misconfigured.

A router has two VRFs: 'RED' and 'BLUE'. An interface is currently in the global routing table. You need to move it to the 'RED' VRF. Which configuration steps are required?

Remove the IP address from the interface, assign the interface to the VRF, then reapply the IP address.

Assign the interface to the VRF without removing the IP address.

Change the VRF name in the global configuration.

Create a new interface and assign it to the VRF.

Which command is used to verify the interfaces that are assigned to a specific VRF on a Cisco IOS XE device?

show ip vrf interfaces CUSTOMER_A

show running-config interface GigabitEthernet0/1

CiscoCertified Network Professional Enterprise

Domain 2Objective 2

2.2 Configure and Verify Data Path Virtualization Technologies 350-401 Practice Questions (Page 4)

Part of the 2.0 Virtualization domain, which accounts for 10% of the 350-401 exam. Cisco does not publish an official question count, but from its 120-minute exam (~50–80 total, ~5–8 in this domain), expect 2–3 from this objective — we provide 34 practice questions to prepare you well beyond it. (estimate)

34questions here

7free pages

8concepts

10%of the exam

Questions 16–20

16application · medium
A network engineer needs to connect two remote sites over an IP-only WAN. The sites use different routing protocols (OSPF and EIGRP) and need to carry multicast traffic between them. Which tunneling technology should be used?
Select an answer first
17foundation · easy
Which configuration element defines the encryption and authentication algorithms used for IPsec data traffic?
Select an answer first
18application · medium
A router has two VRFs: 'BLUE' and 'GREEN'. A user in the BLUE VRF cannot reach a server that is directly connected to the GREEN VRF. The engineer confirms that both VRFs have correct routing tables and that the server's IP is reachable from the GREEN VRF. What is the most likely reason for the failure?
Select an answer first
19application · medium
A router has two VRFs: 'RED' and 'BLUE'. An interface is currently in the global routing table. You need to move it to the 'RED' VRF. Which configuration steps are required?
Select an answer first
20foundation · easy
Which command is used to verify the interfaces that are assigned to a specific VRF on a Cisco IOS XE device?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to 350-401

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Cisco. “350-401” is a trademark of its owner, used for identification only.

2.2 Configure and Verify Data Path Virtualization Technologies 350-401 Practice Questions (Page 4)

Questions 16–20

A network engineer needs to connect two remote sites over an IP-only WAN. The sites use different routing protocols (OSPF and EIGRP) and need to carry multicast traffic between them. Which tunneling technology should be used?

Which configuration element defines the encryption and authentication algorithms used for IPsec data traffic?

A router has two VRFs: 'RED' and 'BLUE'. An interface is currently in the global routing table. You need to move it to the 'RED' VRF. Which configuration steps are required?

Which command is used to verify the interfaces that are assigned to a specific VRF on a Cisco IOS XE device?

Keep studying — 2.0 Virtualization