An administrator needs to configure a custom TCP/IP stack for vMotion traffic. The vMotion network is on a separate subnet with its own gateway. Which steps must be performed to assign this custom stack to vMotion?

Create a distributed port group for vMotion and assign it to the custom stack.

Use the vMotion stack that is already available and modify its gateway.

Create the custom stack, configure its TCP/IP settings, and then select it in the vMotion service settings.

Configure the default stack's routing table and then enable vMotion on that stack.

An organization is deploying vSphere with multiple services that require network isolation. The administrator wants to use custom TCP/IP stacks for vMotion and vSphere Replication. However, the network team has limited IP addresses available. What is the most efficient way to configure the custom stacks while maintaining isolation?

Create two custom TCP/IP stacks, one for vMotion and one for replication, each with its own IP address.

Use the default stack for both services and rely on VLANs for isolation.

Use the vMotion stack for both services and configure a separate gateway for replication.

Create a single custom TCP/IP stack and assign it to both vMotion and replication.

After creating a vSphere Distributed Switch (vDS), what is the next step to make it functional for VM traffic?

Create a distributed port group and connect VMs

Configure the vDS IP address for management traffic

Add ESXi hosts and assign physical NICs to the vDS

Enable LACP on the vDS for link aggregation

What is required to create a custom network stack in vSphere?

A dedicated physical NIC for the stack

A license for vSphere Enterprise Plus

A distributed switch with at least two uplinks

A VMkernel adapter assigned to the custom stack

VMwareCertified Professional - Data Center Virtualization (VCP-DCV)

Domain 3Objective 2

Configure Networking VCP-DCV Practice Questions (Page 2)

Part of the Installing, Configuring, and Setup domain, which makes up ~26% of our current practice bank. VMware does not publish an official question count, but from its 135-minute exam (~55–90 total, ~14–23 in this domain), expect 2–4 from this objective — we provide 28 practice questions to prepare you well beyond it. (estimate)

28questions here

6free pages

8concepts

Questions 6–10

6foundation · easy
Which network stack is specifically designed to handle vMotion traffic in vSphere?
Select an answer first
7application · medium
An administrator needs to configure a custom TCP/IP stack for vMotion traffic. The vMotion network is on a separate subnet with its own gateway. Which steps must be performed to assign this custom stack to vMotion?
Select an answer first
8expert · hard
An organization is deploying vSphere with multiple services that require network isolation. The administrator wants to use custom TCP/IP stacks for vMotion and vSphere Replication. However, the network team has limited IP addresses available. What is the most efficient way to configure the custom stacks while maintaining isolation?
Select an answer first
9foundation · easy
After creating a vSphere Distributed Switch (vDS), what is the next step to make it functional for VM traffic?
Select an answer first
10foundation · easy
What is required to create a custom network stack in vSphere?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to VCP-DCV

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by VMware. “VCP-DCV” is a trademark of its owner, used for identification only.

Configure Networking VCP-DCV Practice Questions (Page 2)

Questions 6–10

Which network stack is specifically designed to handle vMotion traffic in vSphere?

An administrator needs to configure a custom TCP/IP stack for vMotion traffic. The vMotion network is on a separate subnet with its own gateway. Which steps must be performed to assign this custom stack to vMotion?

After creating a vSphere Distributed Switch (vDS), what is the next step to make it functional for VM traffic?

What is required to create a custom network stack in vSphere?

Keep studying — Installing, Configuring, and Setup