An administrator attempts to apply a data protection policy to a volume group, but the operation fails with an error. The policy contains a snapshot rule and a replication rule. What is a likely cause of this failure?

The volume group already has a different data protection policy applied.

The policy was created for volumes only and cannot be applied to volume groups.

The replication rule uses an RPO of 5 minutes, which is not supported for volume groups.

The snapshot rule frequency is set to 1 hour, which is not allowed for volume groups.

A PowerStore administrator wants to verify that a data protection policy is working correctly after applying it to a volume. Which of the following should the administrator check?

The volume's performance metrics to ensure no degradation.

The remote system's storage capacity to ensure it is not full.

The policy's creation timestamp to confirm it was applied.

The replication session status and the list of snapshots for the volume.

A media company uses PowerStore for a file system that holds project assets. They want snapshots every 6 hours, but they also want to keep the last snapshot of each day for 90 days for archival purposes. What is the most efficient way to configure snapshot rules in a data protection policy?

Create two snapshot rules: one with a 6-hour frequency and a retention of 1 day, and another with a daily frequency and a retention of 90 days.

Create one snapshot rule with a daily frequency and a retention of 90 days, and rely on the system to automatically take 6-hour snapshots.

Create one snapshot rule with a 6-hour frequency and a retention of 90 days.

Create two separate policies and apply both to the file system.

A company has a PowerStore volume that is currently protected by a policy with a snapshot rule (daily, 7-day retention) and a replication rule to a remote site. The remote site is being decommissioned, and the replication is no longer needed. The administrator wants to keep the local snapshots but stop replication. What is the correct action?

Disable the remote system in the replication rule, but keep the rule in the policy.

Edit the existing policy to remove the replication rule, leaving the snapshot rule intact.

Remove the policy from the volume and then reapply it after deleting the replication rule.

Delete the entire policy and create a new one with only the snapshot rule, then apply it to the volume.

Dell PowerStore Deploy

Domain 3Objective 2

Configure Data Protection Policies for PowerStore Storage Resources. POWERSTORE-DEPLOY Practice Questions (Page 1)

Part of the PowerStore Administration domain, which accounts for 10% of the POWERSTORE-DEPLOY exam. Dell Technologies does not publish an official question count, but from its 90-minute exam (~35–60 total, ~4–6 in this domain), expect 2–3 from this objective — we provide 15 practice questions to prepare you well beyond it. (estimate)

15questions here

3free pages

8concepts

10%of the exam

Questions 1–5

1application · medium
An administrator attempts to apply a data protection policy to a volume group, but the operation fails with an error. The policy contains a snapshot rule and a replication rule. What is a likely cause of this failure?
Select an answer first
2application · medium
A PowerStore administrator wants to verify that a data protection policy is working correctly after applying it to a volume. Which of the following should the administrator check?
Select an answer first
3application · medium
A media company uses PowerStore for a file system that holds project assets. They want snapshots every 6 hours, but they also want to keep the last snapshot of each day for 90 days for archival purposes. What is the most efficient way to configure snapshot rules in a data protection policy?
Select an answer first
4application · medium
A global company replicates a PowerStore volume from its primary data center in New York to a secondary site in London. The network latency between the sites is 80 ms. The RPO requirement is 30 minutes. Which replication mode should be selected in the replication rule?
Select an answer first
5application · medium
A company has a PowerStore volume that is currently protected by a policy with a snapshot rule (daily, 7-day retention) and a replication rule to a remote site. The remote site is being decommissioned, and the replication is no longer needed. The administrator wants to keep the local snapshots but stop replication. What is the correct action?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to POWERSTORE-DEPLOY

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Dell Technologies. “POWERSTORE-DEPLOY” is a trademark of its owner, used for identification only.

Configure Data Protection Policies for PowerStore Storage Resources. POWERSTORE-DEPLOY Practice Questions (Page 1)

Questions 1–5

An administrator attempts to apply a data protection policy to a volume group, but the operation fails with an error. The policy contains a snapshot rule and a replication rule. What is a likely cause of this failure?

A PowerStore administrator wants to verify that a data protection policy is working correctly after applying it to a volume. Which of the following should the administrator check?

A media company uses PowerStore for a file system that holds project assets. They want snapshots every 6 hours, but they also want to keep the last snapshot of each day for 90 days for archival purposes. What is the most efficient way to configure snapshot rules in a data protection policy?

A global company replicates a PowerStore volume from its primary data center in New York to a secondary site in London. The network latency between the sites is 80 ms. The RPO requirement is 30 minutes. Which replication mode should be selected in the replication rule?

Keep studying — PowerStore Administration