Which of the following is a hardware readiness check for EDP deployment?

Confirm the server has a TPM 2.0 chip for encryption

Verify that the server has sufficient RAM to meet EDP requirements

Ensure the server has a DVD drive for installation

Check that the server's power supply is 80 Plus Gold certified

An administrator is validating the network configuration for a Dell EDP deployment. The EDP nodes are assigned static IP addresses in the 10.10.20.0/24 subnet, and the gateway is 10.10.20.1. During the check, the administrator pings the gateway from each node successfully but cannot ping the DNS server at 10.10.30.10. The routing table on the nodes shows a default route via 10.10.20.1. What should the administrator verify next?

Add a static route on each node to the DNS server via the gateway.

Disable the firewall on the nodes to allow DNS traffic.

Confirm that the DNS server is reachable from the gateway device.

Change the node IP addresses to be in the same subnet as the DNS server.

After completing all EDP pre-deployment checks, a technician records the results in a spreadsheet. The technician notes that the network latency test between the two EDP nodes showed 5 ms, which is within the acceptable range. However, the technician forgets to record the firmware version of the BIOS. What is the most appropriate action?

Mark the BIOS check as 'not applicable' because it is a hardware component, not software.

Estimate the BIOS version based on the server model and record that.

Re-run the hardware check to obtain the BIOS version and add it to the documentation.

Proceed with deployment because the BIOS firmware was checked and is not required to be documented.

A technician is verifying hardware readiness for an EDP deployment. The Dell PowerEdge servers have the correct CPU and memory, but the technician notices that one server has a different network card model than the other two servers. The Dell EDP support matrix lists the network card model on the two servers as supported, but the third server's card is not listed. What should the technician do?

Update the support matrix to include the network card model.

Use the server with the unlisted card as a spare and deploy with only two servers.

Proceed because the network card is functional and will work with the OS.

Replace the unlisted network card with a model that is listed in the support matrix.

What is the purpose of documenting EDP pre-deployment verification results?

To create a backup of the configuration

To confirm readiness for EDP deployment

To provide a record for auditors

To satisfy Dell's warranty requirements

Dell Networking Design

Domain 4Objective 4

Verify EDP Pre-Deployment Checks Are Complete. NETWORKING-DESIGN Practice Questions (Page 1)

Part of the Documentation domain, which accounts for 16% of the NETWORKING-DESIGN exam.

25questions here

5free pages

6concepts

16%of the exam

Questions 1–5

1foundation · easy
Which of the following is a hardware readiness check for EDP deployment?
Select an answer first
2application · medium
An administrator is validating the network configuration for a Dell EDP deployment. The EDP nodes are assigned static IP addresses in the 10.10.20.0/24 subnet, and the gateway is 10.10.20.1. During the check, the administrator pings the gateway from each node successfully but cannot ping the DNS server at 10.10.30.10. The routing table on the nodes shows a default route via 10.10.20.1. What should the administrator verify next?
Select an answer first
3application · medium
After completing all EDP pre-deployment checks, a technician records the results in a spreadsheet. The technician notes that the network latency test between the two EDP nodes showed 5 ms, which is within the acceptable range. However, the technician forgets to record the firmware version of the BIOS. What is the most appropriate action?
Select an answer first
4application · medium
A technician is verifying hardware readiness for an EDP deployment. The Dell PowerEdge servers have the correct CPU and memory, but the technician notices that one server has a different network card model than the other two servers. The Dell EDP support matrix lists the network card model on the two servers as supported, but the third server's card is not listed. What should the technician do?
Select an answer first
5foundation · easy
What is the purpose of documenting EDP pre-deployment verification results?
Select an answer first

Finished these 5 questions?

Review the revealed explanations, or continue through the curriculum.

Next 5 questions →Back to NETWORKING-DESIGN

Free Basic Practice is a study aid with revealable answers — not a scored exam. Examers.io is independent and not affiliated with or endorsed by Dell Technologies. “NETWORKING-DESIGN” is a trademark of its owner, used for identification only.

Verify EDP Pre-Deployment Checks Are Complete. NETWORKING-DESIGN Practice Questions (Page 1)

Questions 1–5

Which of the following is a hardware readiness check for EDP deployment?

What is the purpose of documenting EDP pre-deployment verification results?

Keep studying — Documentation